Home / cover / HOWTO / install

How To Install Pool Cover Anchors

April 16, 2021

9/16 x 12 bsw brass pool cover anchors. According to the nec (national electric code), bonding is required of any metallic product within 5 feet horizontally and 12 feet vertically of the pools edge and is designed to protect users by equally.

5Star Safety Anchor Industries, Inc. Pool cover

The brass anchors are ¾” and the hole needs to be 2” deep.

How to install pool cover anchors. Measure the pool and the pool cover. Hello i just had my whole yard done in pavers. I have the special poles that are needed for paver installation.

Some older anchors are pop up type. Install the 8 anchors at the 4 corners of the pool (see anchor installation below). Take the difference in width and length and divide by two.

This will determine the overlap of the cover. Posted on october 23, 2015 by davy merino october 16, 2020. Failure to keep top of cover clear may cause water to puddle and failure of pool cover.

Remove all swimming pool ladders and handrails 2. The anchors for this type of cover are flush with the deck when the cover is off the pool. Chalk line should be parallel to pool, this will ensure that all anchors will be aligned.

Place cover over the pool carefully so you do not snag or damage the pool cover. Step 4 snap a chalk line along the perimeter of the pool, using corner anchors 18 from cover as a guide. Our pool covers secure to the deck surface with rustproof brass anchors.

Pool takes a 22′ x 42′ cover. The anchors are typically brass. Brass winter safety pool covers safety cover anchors brass concrete anchors.

A safety cover is one of the best pool products you can buy. Install springs onto straps with equal adjustment. Works with all major pool cover manufacturer/brands.

Both our anchor mesh safety pool cover and defender mesh. Lay the safety cover over pool and adjust for equal overlap at all 4 corners of the pool. Damage that occurs to covers that are not installed properly or maintained properly per the guidelines in this document will not be covered by meyco’s warranty.

If you need to order replacement springs for your pool this is a 5 pack of safety cover springs. As debris collects on top of pool safety cover, cover must be swept to ensure that rain water can drain. Installation of pool lift anchors typically requires bonding of the anchors according to your local code requirements.

These are retractable pool safety cover anchors anchor has an octagon allen head hole for adjustment of screwing the anchors into and out as they are needed 5/8 anchor. Our pool is surrounded by a new belgard paver patio. The “best” pool cover should be secured with the “best” hardware.

Pool cover anchors are used to fasten the straps of winter pool covers to the ground or deck. Stretch the cover over the pool and use buckets of water to hold it in place. For installing a safety cover on a pool with a wooden deck you will require these wood deck anchors for pool safety covers.

Anchor points should be located 18 form the edge of the cover (not the edge of the pool) and in line exactly with the strap. The cause can be pressure around the top few threads, when an anchor is pounded into a hole that is just millimeters too small. A 20′ x 40′ rect.

According to standard sizes : These come in a pack of 10 and you will need one for each strap that your pool cover has. The overlap can vary from 10 to 15 inches.

Does anyone have instructions on how to install the cover on a paver brick surface. With first 8 anchors secured, snap a chalk line along the perimeter of the pool using installed anchors as a guide. They screw down flush to the ground for the the pool season and screw out to provide anchor points for springs attached to the cover straps.

Each of these swimming pool covers is relatively easy to install and remove. Pull cover tightly to remove packing wrinkles and help cover to float on pool surface. How to install pool safety cover anchors.

Stickers are those pool cover anchors that won’t turn up, and/or won’t turn down. If you own or just purchased a pool safety cover, congratulations! Mesh safety covers stretch across your entire pool and protect it and your kids from falling in.

Using a chalk line or piece of string, mark a straight line between corner anchors on all four sides of deck. Install remaining anchors down the length of pool, being sure to locate the anchor on Earlier this year we had a complete renovation done on our inground concrete pool.

Install remaining anchors working from the middle of the pool out, pulling back each strap until cover edge is aligned. Adjust for correct overlap on all sides. • locate and install anchors and springs for straps 5, 6, 7 and 8.

I once installed a safety cover on an inground pool that had no deck. When not in use they recess flush with the deck. Overlap on each side may vary 11″ to 14″.

5/8 x 11 unc brass pool cover anchors : After all the deck anchors are drilled, spend time to adjust strap length to equalize spring compression and to provide better coverage or better fit in certain areas, as needed. Our stainless steel buckles and aluminum strap tips won’t rust or stain your swimming pool decking and our stainless steel wall anchors won’t stain rock walls like others.

Planter & grass cover anchors. An effective replacement for old worn out pool cover anchors. This cover needed many slight adjustments.

Pool • after completing the initial installation of the first 8 anchors, install remaining anchors working from center of the cover to the ends. Pool dealer pool size cover size overlap anchors date installed meyco products relies on the experience and knowledge of pool professionals to properly install our products. After installation, pool safety cover must be inspected for debris accumulating on top of cover.

If the cover has cutouts, adjust for proper alignment now. Remember to alternate sides and to attach and secure each spring as each anchor is installed. I have to put 24 concrete anchors into the concrete surrounding the pool so the loops of the pool cover can attach to them.

I also purchased a new safety pool cover. When all eight corner anchors are installed, adjust the strap through the buckles for proper tension and equal overlap. Slightly (2”) away from the center of the pool to allow for eventual cover stretch.

Safety covers look great, protect the pool while keeping kids safe, and with a 12 year … The pavers are roughly 4 inches thick; Attach springs to cover straps, then install springs on anchors, using installation rod (see spring installation below).

Adjust the anchor Safety cover, Custom pools, Pool cover