Home / apply / HOWTO / veneer

How To Apply Veneer To Plywood Edge

February 03, 2021

The excess veneer on each side and at each end is really easy to trim. I use a little piece of wood to spread the glue.

Formica Faced Birch Plywood Worktop 30mm F0949 White

Use a roller or smooth block of wood to firmly press down the heated section of veneer tape.

How to apply veneer to plywood edge. On this cabinet there are horizontal and vertical edges, but i veneer to appear like one giant piece. That is important so you get a good bond all the way to the edge. Once you have the strips prepared, cut to length and width, clamp your plywood piece upright in a vise.

Sometimes you might find thin veneer edge banding is the best option for a project, but it might be hard to find edge banding that matches the plywood you are working with. Use a roller or smooth block of wood to firmly press down the heated section of veneer tape. If you plan to veneer on an unfinished wood surface or plywood it is recommended that you first seal the surface with a coat of varnish, shellac or polyurethane finish.

Use a roller, brush or putty knife to apply thin even coats on both substrate and the back of the veneer. One option is to use a utility blade or exacto knife if you want, but you’ll be risking cutting into the finished veneer edge, or possibly into the veneer face of the plywood. Allow the finish ample drying time, usually 24 hours, and then continue on with the veneer application.

The glue will be activated by heat. Place the edge strip in the glue and slide it around a bit to smear the glue over both surfaces. While the the edging is still hot , use a roller or smooth block of wood to firmly press down the heated section of veneer tape.

At the time of sale, you will get 1 roll of birch with iron veneer. Apply a generous amount of glue and spread it out so it covers the entire surface of the plywood edge. Applying thin wood veneer edge tape.

This article will discuss applying solid edging to plywood edges. Center the selected pattern section over the substrate panel and apply the contact cement, following the manufacturer's instructions, to both the veneer and the substrate. This will maximize its effectiveness.

Sand plywood and apply edge banding. Use a household iron set on cotton (without steam) to activate the glue, pressing the veneer firmly in place. Heat up your iron to the highest setting without steam.

There are now many varieties of veneer, with applications that have evolved for convenience. After the glue has cooled, use a single cut, mill bastard file to remove the extra veneer from the edges. To apply veneer edge banding:

Apply a thin bead of yellow glue near each side of the plywood edge where the solid edge strip will go. I starte with the wood that i had cut along the grain. It also stiffens the plywood, an important feature for shelving.

Position the squared edge on the edge of your plywood or other substrate and smooth it with a few passes of an iron. Cut a banding strip about 1″ overlength. I typically line up one edge of the veneer with one edge of the substrate so that the veneer is inside the edge of the substrate by an eighth of an inch.

Position the veneer on the plywood edge. Buy a roll that’s slightly wider than the plywood edge. The only tool you need to apply veneer trim is a regular household iron at cotton.

Once the panel has cured, i use my table saw, with a plywood cross cutting blade, to do the final cutting of the panel. Once i fill and sand the joint smooth, this becomes a decent option for concealing the edge of the plywood. This article will address how to apply thin veneer edge banding in the form of iron on veneer tape.

Use a wood block or roller to apply pressure to the tape and seat the blue into the plywood edge. The final way to finish a plywood edge is to apply a thin strip of adhesive veneer, called edge banding. There are a lot of ways to cover these edges from solid wood veneer to thin edge strips to full thickness solid wood edging.

With a roll of wood veneer edge banding and a few simple tools, you can cover raw plywood edges so the plywood is nearly indistinguishable from solid wood. How to apply wood edge banding? Banding is available in many woods and in melamine.

Before applying the edge banding, give the edge to be finished a good sanding. You simply hold the edge banding in place, run over it with a household iron to heat the adhesive, let it cool. Use a wood block or roller to apply pressure to the tape and seat the blue into the plywood edge.

Be sure to mix the adhesive thoroughly before applying it. Roll it back and forth, working the glue into the plywood. The only negative to using plywood is its exposed veneer edges.

That’s why i like to use sandpaper on a sanding block instead. Roll it back and forth, working the glue into the plywood. Cut the veneer to length.

You’ll have some fuzzy edges where you trimmed the veneer flush to the work, but that can be quickly removed with some sandpaper. You can cover raw plywood edges with a roll of wood veneer edge banding and some simple tools. This helps make the plywood nearly indistinguishable from solid wood.

For example, i can use pocket holes to attach a 1x2 to the front edge of this piece of plywood. Cut a strip of edge banding slightly longer than the side of your plywood piece. Plywood is a perfect material for cabinet, bookcase and bookshelf making.

Clamp the plywood in place. Repeat this process until you get within a few inches of the end of tape. Apply psa backed wood veneer to exposed end.

Then i use blue painter's tape to hold it in place. It is typically 7/8 wide to allow for trimming and comes in rolls from 25' to 250' long. And unlike thin veneer edgings, the wood nosing can be routed to create a decorative edge (photo 8).

If you make it even wider than the plywood, as we show in this article, the extra stiffness will help keep plywood shelves from sagging. We advise that you put two coats of cement on the substrate and one coat to the back of the veneer.

Wood Veneer table top with Metal Edge Contract